Crafting Project: Eldritch Horror Storage Solution (Part 1)

August 28, 2017 at 12:33 pm (Art, Board games, Foamcore, Games, Papercraft) (, , , , )


I own all of the expansions for the board game Eldritch Horror. I really enjoy this game, however, it is very cumbersome to set up and tear down this game, especially if you want to use the expansions (I previously have kept each of them separate so I could enjoy each one’s additions). I finally had some time to work on designing my own storage solution that fits into the original game’s box (The provided boxes are horrible for storing the game content).

SOME of the game content that needs to be stored

My plan was to be able to play the game out of the box. The core box would hold the majority of the game content while 1-2 of the big box expansions would hold the additional stuff like the Ancient One decks and Mythos cards (things that aren’t all used in every playthrough, etc). I’m still not done with this project, but I’ve made two substantial components, and I have designs for more stuff.

The first component is a card channel to hold the mini-cards in the game (spells, items, artifacts, etc). I didn’t really want this as a solution and the first designs were to build individual boxes with lids, but the amount of work would have been staggering to make a professional-looking set of boxes with graphics wrap using linen-finish paper. I opted for an easier route, but I made sure each type of card had its own section (as opposed to using loose cardboard dividers, which means the whole thing can fall over if you take the cards out, etc). I estimated how much room would be needed for additional expansions using a calculation of how much each previous expansion took (3 cards = roughly 1mm).

EDIT: Some measurements. I used 5mm foamcore and ~2mm thick chipboard for the dividers.

Total insert dimensions: 286mm x 80mm

Cuts for the divider cards are 2mm and go down about 23mm. I didn’t actually glue them in as they had a snug fit. The spacing of the cuts are [roughly] as follows (measured from the inside of the larger box; basically minus 10mm for both ends). Also, keep in mind the sections are rearranged so the larger ones are on the outsides.

Section (assets/artifacts): 75mm

Section (conditions): 74

Section (unique assets): 67mm

Section (spells): 51mm

 

The next component to build was a box for the game tokens. I’ve seen other people make trays out of foamcore, but I didn’t like the idea of having everything be loose without a lid. The last time I moved, I found that many of my boardgames ended up on their side or upside down in their moving boxes. I’d hate to have to sort through everything all over again. I originally wanted a professional-looking box with list that would be graphics wrapped (possibly with a neodymium magnet in place), but again, I opted for something a bit more simple to make the scope smaller (after all, I’d like to eventually play this game and not be forever working on box inserts).

I decided on making small open-topped boxes out of ~1mm cardboard and then building a casing base and lid. I ended up not gluing these micro-boxes into the casing yet since I may still try to do a graphics wrap on them. I still need to figure out a good process to do the image work, and I’m not sure if there is enough clearance for it. The lid slides on top of it all and the whole component box can be removed.

NOTE: I opted to keep the clues out of this box. I want to make a separate one so I can shake it and mix the tokens up for randomized drawing. I also didn’t add the “general” tokens. This component box fits like an “L” shape to the mini-cards section right now. I’ll add another box for the general pieces most likely or just keep them in a baggie. They are a bit larger and harder to organize.

EDIT: I was asked to provide some measurements. I’d need to clean up my schematics to get rid of the design notes, etc. but I figured I can provide some basics. Keep in mind these are the measurements I used, but could be off by a milimeter or two (based on cuts, measurement precision, and how the pieces are assembled; the cardboard is ~1mm after all)

1x Large Component Box (outer box that holds inner boxes): 199mm x 82mm x ~47mm (total height). The bottom height is 20mm and the lid’s height is 27mm.

3x Component box 1 (larger one): 80mm x 43mm x 45mm (height). Open topped

3x Component box 2 (smaller one): 65mm x 25mm x 45mm (height). Open topped. These go in a group of 3, rotated 90 degrees. They could be wider as well; I apparently did bad math or something.

 

 

Advertisements

Permalink Leave a Comment

Crafting Project: Heroes of Normandie component boxes

August 28, 2017 at 12:13 pm (Art, Board games, Games, Papercraft) (, , , )


I’ve recently purchased a bunch of content for the boardgame/wargame Heroes of Normandie. My wife and I really enjoyed playing this game, but it has a lot of components that all need to be organized if you want any chance of finding anything. Each platoon in the game is represented by a large tile and each squad is another smaller tile. Each squad tile has to be kept with the platoon as well as any platoon-specific vehicles or equipment.

I decided to make a series of cardboard boxes that have the platoon markings on them to keep everything organized. The company that makes the game also has a similar thing, however, it is unreasonably expensive to have it shipped to North America. I made my own.

Permalink Leave a Comment

Crafting project: Pop-up Terrain

August 28, 2017 at 12:04 pm (Art, Foamcore, Papercraft) (, , , , , )


Pop-up Terrain

A few years ago I bought into a Kickstarter that was designing pop-up terrain for roleplaying games. I picked a small building out of this set so I could put it together in a short period of time. A few things in the instructions were a bit iffy, but I completed it (with a couple minor issues). The base is glued to foamcore, while the rest was printed off on cardstock paper.

 

 

 

 

 

Permalink Leave a Comment